Nearby Communities
Introduction
Below you will find our list of the communities that are in the vicinity of the County Farm Cemetery.
Just a reminder ...
Since our focus is on geography, we don't have any burial or interment information. Nor do we have any contact information for the County Farm Cemetery.
List of Neighboring Communities ...
Below are the communities that are within 30 miles [48.3 km]<1> of the County Farm Cemetery. We've listed the following cemeteries based on their distance, with the closest first.
- Dahlonega
(Less than 2 miles to the southeast)
- Jump to our Gazetteer entry for Dahlonega
- Dahlonega is located in Wapello County
- Highland Center
(3 miles [4.8 km] to the northeast)
- Jump to our Gazetteer entry for Highland Center
- Highland Center is located in Wapello County
- Ottumwa
(4 miles [6.4 km] to the south)
- East Ottumwa
(4 miles [6.4 km] to the south)
- Note: The GPS coordinates that we are using for East Ottumwa have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for East Ottumwa
- East Ottumwa is located in Wapello County
- Agency
(7 miles [11.3 km] to the southeast)
- Note: The GPS coordinates that we are using for Agency have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Agency
- Agency is located in Wapello County
- Population from the 2020 Census: 641 people
- Jump to TripAdvisor's Tourism page for Agency <2>
- Hedrick
(7 miles [11.3 km] to the northeast)
- Note: The GPS coordinates that we are using for Hedrick have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Hedrick
- Hedrick is located in Keokuk County
- Population from the 2020 Census: 743 people
- Kirkville
(7 miles [11.3 km] to the northwest)
- Note: The GPS coordinates that we are using for Kirkville have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Kirkville
- Kirkville is located in Wapello County
- Population from the 2020 Census: 177 people
- Chillicothe
(7 miles [11.3 km] to the west)
- Note: The GPS coordinates that we are using for Chillicothe have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Chillicothe
- Chillicothe is located in Wapello County
- Population from the 2020 Census: 97 people
- Cliffland
(8 miles [12.9 km] to the southeast)
- Jump to our Gazetteer entry for Cliffland
- Cliffland is located in Wapello County
- Competine
(8 miles [12.9 km] to the east)
- Jump to our Gazetteer entry for Competine
- Competine is located in Wapello County
- Fremont
(9 miles [14.5 km] to the north)
- Martinsburg
(9 miles [14.5 km] to the northeast)
- Note: The GPS coordinates that we are using for Martinsburg have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Martinsburg
- Martinsburg is located in Keokuk County
- Population from the 2020 Census: 107 people
- Dudley
(10 miles [16.1 km] to the west)
- Jump to our Gazetteer entry for Dudley
- Dudley is located in Wapello County
- Cedar
(11 miles [17.7 km] to the northwest)
- Jump to our Gazetteer entry for Cedar
- Cedar is located in Mahaska County
- Carbon
(12 miles [19.3 km] to the south)
- Note: The GPS coordinates that we are using for Carbon have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Carbon
- Carbon is located in Davis County
- Batavia
(12 miles [19.3 km] to the southeast)
- Abingdon
(13 miles [20.9 km] to the east)
- Jump to our Gazetteer entry for Abingdon
- Abingdon is located in Jefferson County
- Exeelsior
(13 miles [20.9 km] to the northwest)
- Note: The GPS coordinates that we are using for Exeelsior have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Exeelsior
- Exeelsior is located in Mahaska County
- Linby
(13 miles [20.9 km] to the east)
- Jump to our Gazetteer entry for Linby
- Linby is located in Jefferson County
- Pekin
(13 miles [20.9 km] to the northeast)
- Note: The GPS coordinates that we are using for Pekin have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Pekin
- Pekin is located in Jefferson County
- Wright
(13 miles [20.9 km] to the northwest)
- Jump to our Gazetteer entry for Wright
- Wright is located in Mahaska County
- Eddyville
(13 miles [20.9 km] to the northwest)
- Floris
(14 miles [22.5 km] to the south)
- Jump to our Gazetteer entry for Floris
- Floris is located in Davis County
- Population from the 2020 Census: 143 people
- Eldon
(14 miles [22.5 km] to the southeast)
- Hayesville
(14 miles [22.5 km] to the northeast)
- Note: The GPS coordinates that we are using for Hayesville have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Hayesville
- Hayesville is located in Keokuk County
- Population from the 2020 Census: 48 people
Off-the-Road Links ...
The official website for State of Iowa: https://www.iowa.gov/
Footnotes ...
<1> | Our distances are not driving distances, but are calculated as a 'point-to-point' distance. A straight line distance ignores things like rivers, canyons, lakes, et cetera - it's truly a line drawn from Point A (ie- ) to Point B.Our distance measurements begin at a specific point at the County Farm Cemetery. The point we use is located at these GPS coordinates - Latitude: 41.0778, Longitude: -92.3891 In this case, the coordinates for the County Farm Cemetery have been provided by the Geographic Names Information System (GNIS). |
<2> | While we're fans and frequent users of TripAdvisor, you should know that we're also members of the TripAdvisor affiliate program. |
<3> | The location has been supplied by the Geographic Names Information System - which is maintained by the U.S. Geological Survey (USGS). While these values should be definitive, we found that accuracy can vary and you should double-check the location if accuracy is required. |