TripAdvisor Links
Introduction ...
Whether we're planning a trip and want to make reservations or still at home and looking for a place to eat, we usually start by visiting the TripAdvisor website. Once on their website we search for what's available, then check the recommendations and experiences of other people.
Although there are many ways of searching the TripAdvisor website, we prefer to start with the TripAdvisor Tourism page. On the Tourism page you'll find a quick overview of the community, with links to restaurants, lodging, flights, rentals and nearby attractions.
In addition, you'll find a link to the TripAdvisor Forum for Custer. If you have a question about your travel plans, post it on their Forum and see if others can give you an answer.
All of this can be found on the TripAdvisor's Tourism page for Custer.
The following list should help you find nearby communities that also have TripAdvisor pages.
List of Neighboring TripAdvisor Tourism Pages ...
Below is a list of those communities which have a TripAdvisor Tourism page and are relatively close to Custer - within 30 miles [48.3 km]<1>.
Our list sorts the communities in alphabetical order. There are 14 communities listed:
- Blackhawk
(30 miles [48.3 km] to the northeast)- Jump to our Gazetteer entry for Blackhawk
- Blackhawk is located in Meade County
- Jump to TripAdvisor's Tourism page for Blackhawk <2>
- Buffalo Gap
(23 miles [37 km] to the southeast)- Jump to our Gazetteer entry for Buffalo Gap
- Buffalo Gap is located in Custer County
- Population from the 2020 Census: 144 people
- Jump to TripAdvisor's Tourism page for Buffalo Gap <2>
- Fairburn
(20 miles [32.2 km] to the east)- Note: The GPS coordinates that we are using for Fairburn have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Fairburn
- Fairburn is located in Custer County
- Population from the 2020 Census: 99 people
- Jump to TripAdvisor's Tourism page for Fairburn <2>
- Hermosa
(21 miles [33.8 km] to the east)- Note: The GPS coordinates that we are using for Hermosa have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Hermosa
- Hermosa is located in Custer County
- Population from the 2020 Census: 409 people
- Jump to TripAdvisor's Tourism page for Hermosa <2>
- Hill City
(11 miles [17.7 km] to the north)- Note: The GPS coordinates that we are using for Hill City have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Hill City
- Hill City is located in Pennington County
- Population from the 2020 Census: 1,074 people
- Jump to TripAdvisor's Tourism page for Hill City <2>
- Hot Springs
(23 miles [37 km] to the south)- Jump to our Gazetteer entry for Hot Springs
- Hot Springs is located in Fall River County
- Population from the 2020 Census: 3,502 people
- Jump to TripAdvisor's Tourism page for Hot Springs <2>
- Keystone
(12 miles [19.3 km] to the northeast)- Jump to our Gazetteer entry for Keystone
- Keystone is located in Pennington County
- Population from the 2020 Census: 352 people
- Jump to TripAdvisor's Tourism page for Keystone <2>
- Nemo
(29 miles [46.7 km] to the north)- Jump to our Gazetteer entry for Nemo
- Nemo is located in Lawrence County
- Jump to TripAdvisor's Tourism page for Nemo <2>
- Newcastle
(30 miles [48.3 km] to the west)- Jump to our Gazetteer entry for Newcastle
- Newcastle is located in Weston County (WY)
- Population from the 2020 Census: 3,314 people
- Jump to TripAdvisor's Tourism page for Newcastle <2>
- Oral
(29 miles [46.7 km] to the southeast)- Note: The GPS coordinates that we are using for Oral have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Oral
- Oral is located in Fall River County
- Estimated population in 2014: 206 people
- Jump to TripAdvisor's Tourism page for Oral <2>
- Pringle
(10 miles [16.1 km] to the south)- Note: The GPS coordinates that we are using for Pringle have been provided by the GNIS.<3> The coordinates still need to be verified.
- Jump to our Gazetteer entry for Pringle
- Pringle is located in Custer County
- Population from the 2020 Census: 109 people
- Jump to TripAdvisor's Tourism page for Pringle <2>
- Rapid City
(28 miles [45.1 km] to the northeast)- Jump to our Gazetteer entry for Rapid City
- Rapid City is located in Pennington County
- Population from the 2020 Census: 78,864 people
- Jump to TripAdvisor's Tourism page for Rapid City <2>
- Rochford
(25 miles [40.2 km] to the north)- Jump to our Gazetteer entry for Rochford
- Rochford is located in Pennington County
- Jump to TripAdvisor's Tourism page for Rochford <2>
- Rockerville
(17 miles [27.4 km] to the northeast)- Jump to our Gazetteer entry for Rockerville
- Rockerville is located in Pennington County
- Estimated population in 2014: 144 people
- Jump to TripAdvisor's Tourism page for Rockerville <2>
Off-the-Road Links ...
Unfortunately, we don't know of an official website for Custer. If you can help, please contact us through our Feedback Page.
The official website for State of South Dakota: sd.gov/
Footnotes ...
| <1> | Our distances are not driving distances, but are calculated as a 'straight-line' (or point-to-point) distance. A straight line distance ignores obstructions like rivers, canyons, lakes, et cetera - it's truly a line drawn from Point A (ie- Custer) to Point B.Our distance measurements begin at a specific point in Custer. The point we use is located at these GPS coordinates - Latitude: 43.7664, Longitude: -103.6013 In this case, the coordinates for Custer have been provided by the Geographic Names Information System (GNIS). |
| <2> | While we're fans and frequent users of TripAdvisor, you should know that we're also members of the TripAdvisor affiliate program. |
| <3> | The location has been supplied by the Geographic Names Information System - which is maintained by the U.S. Geological Survey (USGS). While these values should be definitive, we found that accuracy can vary and you should double-check the location if accuracy is required. |